- Coats Wheel Balancer Parts
- Coats 1004 Wheel Balancer Manual Transmission
- Coats 1004 Wheel Balancer Manual Free
- Coats 1004 Wheel Balancer Manual Transmission
1996 Coats 1004 Wheel Balancer Unit is in good working order and comes with minimal cone assortment. Specifications: Cycle time 4-5 seconds, max. Outer tire diameter is 42”, wheel dia. 10” – 19.9”, wheel width 2.7” – 18.6”, modified tongue motor with: 900 RPM rating, forced air cooling, 1-1/2 HP rating, shipping weight 550 lbs. A video wheel balancer for cars and light trucks, the geodyna ® 9000p features fully automatic non-contact acquisition of all data via 3D imaging technology and five high-resolution cameras, the Power Clamp clamping system, pinpoint easyWEIGHT laser, plus a touch screen interface for unequaled usability, performance and precision. OEM Part# 110543. Up for sale is a replacemnet Coats Wheel Balancer Manual Hub Nut. This Hub Nut will work with most coarse thread 28.5 mm shafts. This includes but is not limited to Coats Models 600, 650, 700, 850, 950, 1001, 1004 and 1050. Coats 1001 wheel balancer manual Description: -The use of the N45 high performance magnet, fixed plate made of carbon fiber board material -Maglev-method was adopted on the center fixing axis to balance the tested products with zero resistance. Manual Part No.: 85009054 01. HENNESSY INDUSTRIES INC. Manufacturer of AMMCO ®, COATS ® and BADA ® Automotive Service Equipment and Tools. Revision: 03/08. WHEEL BALANCER. Installation Instructions. Operating Instructions. Safety Instructions. Maintenance Instructions.
Advertising
Connect to Power
Your factory trained COATS
®
Service Technician should do the
final check to verify the power installation before connecting the
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
Connect the balancer to an appropriate electrical receptacle.
Refer to Figure 8 and 9, as well as Electrical Requirements on
page 1.
page 1.
![Coats 1004 Wheel Balancer Manual Coats 1004 Wheel Balancer Manual](https://i.ytimg.com/vi/RFYNhrUfbyA/hqdefault.jpg)
Note: If pedestrian or equipment traffic might damage the
standard power cord, power outlets must be enclosed in a race-
way on the floor or in an overhead drop.
way on the floor or in an overhead drop.
Note: Electric outlets must be solidly connected. There should
be less than 1 Ω electrical resistance between the ground pin
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
Note: The green wire in the cord is the grounding wire. Never
connect the green wire to a live terminal.
Initial Testing
This should be performed by your factory trained COATS
®
Service Technician.
1. If the circuit breaker for the balancer outlet is off, turn it on
Officemui.msi download full. now. Turn the balancer ON/OFF switch to ON.
Remember: To maintain the proper operating temperature for
the balancer, the unit should be left on all day.
2. The displays will show zeros when the unit is first turned
on. Press any key to continue.
3. Verify that the fan is running by placing your hand between
the arbor faceplate and the motor housing. You should feel air
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
4. Lower the hood and press START. The arbor faceplate
should spin in the direction indicated by the label at the outer
edge of the motor cover (clockwise when viewed straight on).
edge of the motor cover (clockwise when viewed straight on).
If the faceplate spins counterclockwise, turn the balancer off,
turn the circuit breaker off, and disconnect the balancer plug.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Note: Single-phase balancers will also spin in a clockwise
direction.
Note: Disregard a short spin cycle with HUB displayed on the
control panel during this initial testing.
5. Raise the hood during a spin cycle to verify that the hood
interlock system is functioning properly.
Direct Drive
COATS 1000/1000D Wheel Balancer • 5
Figure 8 - Three-Phase Wiring Diagram
Figure 9 - Single-Phase Wiring Diagram Parallel desktop mac 12 crack torrent pirate bay download.
Three-Phase
Ground
Hot
195-230 V
Between
Hot Wires
Between
Hot Wires
Hot
Hot
Single-Phase
A – Red
Coats Wheel Balancer Parts
B – Black
Green/
Coats 1004 Wheel Balancer Manual Transmission
Ground
Advertising
Coats 1004 Wheel Balancer Manual Free
Popular Brands
Popular manuals
Coats 1004 Wheel Balancer Manual Transmission
Coats 1001 Wheel Balancer Manual
|